Mapei · Epoxy floor coatingNo. 25 / 47
Mapefloor FC 200 ME
High build epoxy resin floor coating.
High build epoxy resin floor coating
- Chemical and pharmaceutical industries
- Foodstuffs industry
- Car Parks
- Aseptic rooms
- Warehouses
- Shopping centers
- Factories, hangars, workshop and garages
- Consumption
- 0.32 kg/m² per coat
- Packs we stock
- Part A 22 kg · Part B 3.5 kg
- Colour
- Light grey
Coverage calculator
How much you need.
The arithmetic uses Mapei's published consumption for Mapefloor FC 200 ME and the pack sizes we stock. Set your own wastage allowance.
You need
x 25.5 kg kit (A 22 kg + B 3.5 kg)
- Data sheet quantity
- 12.8 kg
- With 10% wastage
- 14.1 kg
The figures behind it.
- Primer: (if required) Primer SN (A+B): 0.15-0.25 kg/m² (depending on the substrate condition).
- 1st coat: Mapefloor FC 200 ME (A+B ): 0.32 kg/m²
- Finishing coat: Mapefloor FC 200 ME (A+B): 0.32 kg/m²
- 1st coat: Mapefloor FC 200 ME (A+B ): 0.35-0.40 kg/m².
- Broadcast with Quartz 0.5 at 0.5-1.0 kg/m².
- Finishing coat: Mapefloor FC 200 ME (A+B): 0.35-0.40 kg/m².
Mapei's systems use a first coat and a finishing coat. Primer SN and broadcast quartz are separate products.
Consumption on site depends on the substrate, the tool and the applicator, which is why wastage is yours to set. The result is a quantity to plan and quote with, not a guarantee of coverage. Confirm the system against the current Mapei technical data sheet before ordering.
Application
Where it is used.
In Mapei's own words, from the technical data sheet.
- 01Chemical and pharmaceutical industries
- 02Foodstuffs industry
- 03Car Parks
- 04Aseptic rooms
- 05Warehouses
- 06Shopping centers
- 07Factories, hangars, workshop and garages
Where it is not the right product.
- Do not apply the product directly on substrates with moisture content higher than 4% and/or with capillary rising damp
- Do not apply Mapefloor FC 200 ME on dusty substrates
- Do not apply Mapefloor FC 200 ME on substrates with oil or grease stains or stains in general
- Do not dilute Mapefloor FC 200 ME with solvent or water
- The air's relative humidity should not be greater than 75%
Specification
Technical data.
- Colour
- RAL colours
- Mixing Ratio
- Component A: Component B = 22: 3.5
- Mix Density (A+B) (g/cm3)
- 1.50
- Pot life
- 35-45 min
- Overcoating time
- 20 h
- Set to foot traffic
- 24 h
- Set to vehicular traffic
- 48 h
- Application temperature range
- from +5°C to +35°C
- Compressive strength (ASTM C 579 - 01/B) (N/mm²)
- >80
- Compressive strength (EN 196-1) (N/mm²)
- 40
- Bond strength (ASTM D4541) (N/mm²)
- ≥ 1.5
- Taber test (CS17 wheel; 1000g; 1000 cycles) (ASTM D 4060-10)
- 95
Typical values as Mapei prints them in data sheet edition 6782-8-2023 (UAE). They are not a specification for your project: the current Mapei data sheet is.
On site
Packs, mixing and storage.
- We stock
- Part A 22 kg · Part B 3.5 kg
- Mapei packaging
- 25.5 kg kits (component A = 22 kg; component B = 3.5 kg) in containers.
- Mixing
- Mixing Ratio: Component A: Component B = 22: 3.5
- Storage
- The product must be stored in its original packaging in a dry place at a temperature of between +5°C and +35°C. Maximum 24 months.
Related products
Resin Flooring & Coatings.
Self-levelling epoxy floorMapefloor I 300 SL MEPart A 17 kg · Part B 5 kg · Part C 25 kg
Polyurethane-cement floorMapefloor CPU+/MFPart A 2 kg x 2 · Part B 2.16 kg x 2 · Part C 20 kg · Mapecolor CPU+ 0.23 kg
Polyurethane floor finishMapefloor Finish 415 MEPart A 10 kg · Part B 2.5 kg- Mapefloor Finish 450 MEPolyurethane floor finishMapefloor Finish 450 MEPart A 18.9 kg · Part B 3.6 kg
Mapefloor FC 200 ME in Tanzania
Tell us the area. We will quote the job.
Sahihi is an authorized Mapei distributor in Dar es Salaam. Send the quantity of Mapefloor FC 200 ME you need, or describe the job and we will work it out with you.