Mapei · Tile adhesiveNo. 03 / 47
Adesilex P7
High-performance cementitious adhesive with no vertical slip for ceramic and porcelain tiles.
High-performance cementitious adhesive with no vertical slip for ceramic and porcelain tiles
- Interior and exterior bonding of ceramic tiles, porcelain and mosaics on floors, walls and ceilings
- Conventional renders or cementitious mortar on walls
- Interior aerated concrete block walls
- Gypsum or anhydrite after having first applied Primer G
- Cementitious screeds, as long as they are sufficiently cured and dry
- Interior painted walls, as long as the paint is firmly anchored
- Tile on tile of existing flooring with tiles up to 900 cm²
- Bonding on irregular floor substrates and renders, without levelling, to a thickness of 15 mm
- Class
- C2T
- Consumption
- 2.5-3 kg/m² with a No. 5 trowel
- Pack we stock
- 25 kg
- Colours
- Grey · White
Coverage calculator
How much you need.
The arithmetic uses Mapei's published consumption for Adesilex P7 and the pack sizes we stock. Set your own wastage allowance.
You need
x 25 kg bag
- Data sheet quantity
- 50-60 kg
- With 10% wastage
- 55-66 kg
The figures behind it.
- in general (trowel n. 4): 2 kg/m²
- normal sizes (trowel n. 5): 2.5-3 kg/m²
- Large sizes, exterior floors (trowel n. 6): 4 kg/m²
- Foam, etc.: approx. 0.5-0.8 kg/m²
- Gypsum board panels, foamed concrete: approx. 1.5 kg/m²
Consumption on site depends on the substrate, the tool and the applicator, which is why wastage is yours to set. The result is a quantity to plan and quote with, not a guarantee of coverage. Confirm the system against the current Mapei technical data sheet before ordering.
Application
Where it is used.
In Mapei's own words, from the technical data sheet.
- 01Interior and exterior bonding of ceramic tiles, porcelain and mosaics on floors, walls and ceilings
- 02Conventional renders or cementitious mortar on walls
- 03Interior aerated concrete block walls
- 04Gypsum or anhydrite after having first applied Primer G
- 05Cementitious screeds, as long as they are sufficiently cured and dry
- 06Interior painted walls, as long as the paint is firmly anchored
- 07Tile on tile of existing flooring with tiles up to 900 cm²
- 08Bonding on irregular floor substrates and renders, without levelling, to a thickness of 15 mm
Where it is not the right product.
- On precast and poured concrete walls
- On walls or floors subject to extreme flexing or vibration (wood, fibre-cement, etc.)
- On metal surfaces
Specification
Technical data.
- EN 12004 · C2T
- ISO 13007-1 · C2T
- ANSI A118.4 · In compliance with
- EMICODE · EC1 R PLUS - very low emission
- Colour
- grey or white
- Mixing ratio
- 100 parts Adesilex P7 with 26-28 parts of water by weight for Adesilex P7
- Density of the mix (kg/m³)
- 1600
- Pot life
- over 8 hours
- Application temperature range
- from +5°C to +40°C
- Open time (EN 1346)
- 20 minutes
- Adjustability time
- approx. 60 minutes
- Ready for grouting on wall
- after 4-8 hours depending on absorbency
- Ready for grouting on floors
- after 24 hours
- Set to light foot traffic
- 24 hours
- Ready for use
- 14 days
- Bonding strength in compliance with EN 1348 (N/mm2): - initial bonding after 28 days
- 1.4
Typical values as Mapei prints them in data sheet edition 61-12-2017 (UAE). They are not a specification for your project: the current Mapei data sheet is.
On site
Packs, mixing and storage.
- We stock
- 25 kg
- Mapei packaging
- Adesilex P7 white and grey are available in 25 kg bags.
- Mixing
- Use 26-28 parts of water for every 100 parts by weight of Adesilex P7, which is equal to 6.5-7.0 L of water for every 25 kg of Adesilex P7.
- Storage
- Adesilex P7 can be stored 12 months in a normal environment in original packaging.
Related products
Tile Adhesives, Grouts & Care.
Adesilex P7 in Tanzania
Tell us the area. We will quote the job.
Sahihi is an authorized Mapei distributor in Dar es Salaam. Send the quantity of Adesilex P7 you need, or describe the job and we will work it out with you.